NANA Construction, LLC

General

• Responsible for erecting, disassembling, moving, repairing, maintaining, and daily pre work inspections on scaffolding components and systems.
• Erecting, dismantling, modifying, and repairing scaffolding.
• Carry scaffolding components from staging area to erection location.
• Climb scaffolds and work at heights while adhering to company procedures and protocol while working at heights 100% tie off.
• Determine the maximum intended load carrying capacity of the type of scaffolding being used.
• Use hand and power tools safely and correctly.
• Identify all hazards associated with erecting, dismantling, and modifying scaffolding such as electrical hazards and required working distances from electrical power lines and electrical cabling.
• Determine safe mitigations for dropped objects, and falling from heights.
• Able to properly assemble fall restraint and fall protection systems adhering to OSHA and MSHA’s policy’s and procedures.

Journeyman Scaffold Builder

• Responsible for erecting, disassembling, moving, repairing, maintaining, and daily pre work inspections on scaffolding components and systems.
• Carry scaffolding components from staging area to erection location.
• Climb scaffolds and work at heights while adhering to company procedures and protocol while working at heights 100% tie off.
• Determine the maximum intended load carrying capacity of the type of scaffolding being used.
• Use hand and power tools safely and correctly.
• Identify all hazards associated with erecting, dismantling, and modifying scaffolding such as electrical hazards and required working distances from electrical power lines and electrical cabling.
• Determine safe mitigations for dropped objects, and falling from heights.
• Able to properly assemble fall restraint and fall protection systems adhering to OSHA and MSHA’s policy’s and procedures.

Technician

• Works on construction projects, usually working in utility capacity, by transferring from one task to another where demands require a worker with varied experience and ability to work without close supervision by performing the following duties.
• Loading and unloading tools or raw materials.
• Proficient at erecting scaffolding or other pieces of equipment.
• Knowledge of the use of air bags for lifting pipes in rack.
• Cuts and strips/install insulation on piping.
• Other related duties may be assigned.

GMT/Blanket Technician

Quality Control

• Plans, coordinates, and directs quality program designed to ensure quality control and quality assurance of the production of products consistent with established standards.
• Formulates and maintains quality objectives complementary to corporate policies and goals.
• Interprets quality philosophy to key personnel in organization.
• Develops and initiates standards and methods for inspection, testing, and evaluation.
• Plans and oversees the analysis, inspection, design, test, and/or integration to assure the quality of assigned product or component.
• Performs quality engineering reviews of design documentation for compliance with stated requirements.
• Applies statistical process control (SPC) methods for analyzing data to evaluate the current process and process changes.
• Decides whether to accept a product or continue business with a vendor based on a review by the quality assurance engineer.
• Reviews all data obtained during all quality control and quality assurance activities to ensure consistency with company policies and procedures.
• Develops new approaches to solve problems identified during quality activities.
• Keeps management team abreast of significant issues or developments identified during quality activities and actions being taken to improve the situation.
• Prepares and presents technical and program information to the management team.
• Directs workers engaged in inspection and testing activities to ensure continuous control over materials, facilities, and products.
• Maintains a working knowledge of government and industry quality codes and standards.
• Designs and implements quality training programs to key personnel in conjunction with managers.
• Investigates and adjusts customer complaints regarding quality.

Quality Control Supervisor

• Perform manual labor in support of CUI (Corrosion under Insulation) projects
• Proficient in the use of small hand and power tools
• Erect/dismantle scaffolding
• Knowledge of air bags for lifting pipes
• Remove/install insulation and sheetmetal on piping
• Perform manual labor tasks including digging, lifting, material handling, and site preparation
• Maintain compliance with required HSE Training and safety standards
• Participate in safety meetings and maintain a safe work environment

General Maintenance Technician

• Cleans, abrasive blast & sprays surfaces of manufactured products with cleaning and protective or decorative material
• Cleans grease and dirt from products
• Removes rust from metal surfaces with blasting agents
• Applies masking tape over parts and areas that are not to be coated.
• Fills cavities and dents with putty to attain smooth surface.
• Selects and mixes coating liquid to produce desired color.
• Pours coating liquid into spray container and connects gun to air hose.
• Turns sprayer valves and nozzle to regulate width and pressure of spray.
• Pulls trigger and directs spray onto work surface to apply prime or finish coat.
• Coats areas inaccessible to hand sprayer with brush or other means
• Cleans spraying equipment and brushes with solvent.
• Immediately report all Incidents/Accidents, no matter how small, to their Supervisor.

Coating Technician

• Plans, lays out, positions, aligns, and fits together fabricated parts of structural metal products.
• Welds, tacks and assembles together metal components of products such as modules, structural steel, pipe racks and plate welding with electric arc-welding equipment by performing the following duties.
• Works at heights while tied off, assembly & disassembly of temporary structures used during construction.
• Spotting for equipment, rigging & signaling as needed.

Structural Welder/Fitter

• Develop, implement, analyze and maintain comprehensive, integrated project schedules and cost baselines predicated on through analysis of project requirements by applying advanced project controls and business system techniques.
• Maintains project controls by performing training, auditing, and assisting the project control team with estimating, forecasting costs, schedules, and labor.
• Develop, implement, analyze and maintain critical path method logic diagrams that require critical path analysis for time and resource management of manpower, or equipment or facilities.
• Perform complex analysis and summarize data to validate project control parameters with consideration given to performance, reliability, maintainability and cost/schedule control criteria.
• Evaluate changes in procedures or system design and communicate recommended solutions to management.
• Assess potential cost and schedule impacts.
• Coordinate and maintain cost/planning/schedule database operations, and review and analyze project control data or results, and assist in preparation of management reports along with corresponding recommendations.
• Participate in planning meetings as appropriate and gather data for database input.
• Investigate all deviations from established cost and and schedule baselines, appraise and make recommendations to management concerning corrective actions or workarounds to meet established objectives.
• Prepared and issue periodic status/critical items reports to management that highlight significant program issues and potential delays to project milestones and financial objectives.
• Develop, implement, analyze and maintain cost and schedule trend program, baseline change project and forecast process.
• May lead review meetings or assume primary role in the responsibility for the scheduling portion of the division, department or project plan-of-the-day meeting.
• Estimates and forecasts all information related to costs, schedules, and labor for a given project.
• Directs the development of material and labor takeoffs.
• Establishes the baseline budget and schedule for the project.

Journeyman Scaffold Builder

Journeyman Scaffold Builder

GMT/Blanket Technician

Quality Control Supervisor

General Maintenance Technician

Coating Technician

Structural Welder/Fitter

Project Controls Specialist